NSN 101CH0RS

A flat metal or plastic item of various peripheral shapes having a solid (not laminated) cross-section. It is designed to maintain a predetermined distance between two surfaces. For round items without a hole having a solid rectangular cross-section use disk, solid, plain. For round or hexagonal items with only one hole centrally located and with the length (thickness) exceeding 25 percent of the outside diameter or distance across peripheral flats, see spacer, sleeve. The thickness between the two parallel bearing surfaces must be 0.006 inch, (0.152 mm) or more for items less than 1/4 inch (6.35 mm) across the peripheral diameter, or smallest overall outside dimension, or must be 0.016 inch (0.406 mm) or more for items 1/4 inch (6.35 mm) or greater across the peripheral diameter or smallest overall outside dimension. For items with a thickness less than those indicated above, see shim. For items with one hole centrally located conforming to the above dimensional criteria use washer, flat or spacer, ring as applicable. When thickness and/or outsidediameter or smallest overall outside dimension is designated as a tolerance /dimension the maximum dimension will be used to determine compliance. Excludes:gasket; insulator (as modified) and mounting pad, electrical-electronic component.

0.625 inches minimum and 0.645 inches maximum aperture diameter, 4 bolt hole quantity, 0.032 inches nominal cross-sectional height, 0.719 inches nominal center to center distance between bolt holes along length, 0.719 inches nominal center to center distance between bolt holes along width.

NSN 5999-00-413-4916 Datasheet

(NSN) National Stock Number

5999-00-413-4916

(FSG) Federal Supply Group

59 - Electrical and Electronic Equipment Components

(FSC) Federal Supply Classification

5999 - Miscellaneous Electrical and Electronic Components

(NIIN) National Item Identification Number

00-413-4916

Requires Demilitarization

Yes

(INC) Item Name Code

20281

Date

Fri, May 1, 1970

Schedule B Code

8543909000

Aperture Diameter

0.625 inches minimum and 0.645 inches maximum

Bolt Hole Quantity

4

Center To Center Distance Between Bolt Holes Along Length

0.719 inches nominal

Center To Center Distance Between Bolt Holes Along Width

0.719 inches nominal

Cross-Sectional Height

0.032 inches nominal

Cross-Sectional Shape Style

emi

Hole Diameter

0.156 inches nominal

Material Document And Classification

unable to decode

Material

unable to decode

Outside Corner Radius

0.141 inches nominal

Outside Edge To Bolt Hole Center Distance Along Width

0.140 inches nominal

Outside Edge To Bolt Hole Center Distance Along Length

0.140 inches nominal

Overall Length

0.985 inches minimum and 1.010 inches maximum

Overall Width

0.985 inches minimum and 1.010 inches maximum

Precious Material And Location

emi/rfi conductive particles silver

Precious Material

silver

Style Designator

non-circular

Surface Treatment

unable to decode

Temp Rating

-45.0 celsius and 125.0 celsius

Identification

Demilitarization Code

A - Items subject to the export administration regulations (ear) in parts 730-774 of title 15, code of federal regulations (cfr) (ccli or ear99) and determined by dod to present a low risk when released out of dod control. No demil, mut, or end use certificate is required. May require an export licensefrom doc.

Precious Metals Indicator

S - Item contains silver.

Hazardous Metals Indicator

P - Indicates there is no information in the hmirs. The nsn is in a fsc in table ii of fed std 313 and a msds may be required by the user. The requirement for a msds is dependent on a hazard determination of the supplier or the intended end use of item.

Pseudo Item Name Code

0020281

Cross Reference

CAGE Codes

18565

Parker-Hannifin Corporation Dba Pneutronics Div Chomerics Division

U.s./canadian manufacturers

18876

Us Army Aviation and Missile Command

Government departments or units, including military organizations

18536

Celanese Corp

U.s./canadian manufacturers

53711

Naval Sea Systems Command

U.s./canadian manufacturers

16236

Dla Land and Maritime Dba Engineering and Technical Support Div Document Standardization Division (vendor Item Drawings)

Government departments or units, including military organizations

56996

Department of the Army Hq United States Army Communications Research and Development Command

U.s./canadian manufacturers

96169

Electric Boat Corporation Div General Dynamics Electric Boat

Non-manufacturers

Freight Information

Air Commodity

HZ -

Air Dimension

A - Shipment is not a consolidation and does not exceed 84 inches in any dimension.

National Motor Freight Class Rating

M - 85.0

Special Handling

9 - Other or no special handling required (sh)

Type of Cargo

Z - No special type of cargo code applicable

Uniform Freight Classification Item Number

35070

Water Commodity

723 - Radio parts and equipment, excluding tubes packed separately

National Motor Freight Classification Item Number

062800

Schedule B & Trade

Schedule B

8543-90-9000

Description

electrical machines and apparatus parts, nesoi

End Use

20005 - Electric apparatus

Unit of Quantity

NO

USDA

Yes

(SITC) Standard International Trade Classification

77879

(NAICS) North American Industrial Classification System

335999

Questions & Answers

1. What is the FSCG of the NSN 5999-00-413-4916?

   The FSCG of the NSN 5999-00-413-4916 is 5999

2. Does the NSN 5999-00-413-4916 have a Schedule B code assigned?

   Yes, the Schedule B code is 8543909000

3. Does NSN 5999-00-413-4916 require demilitarization?

   Items subject to the export administration regulations (ear) in parts 730-774 of title 15, code of federal regulations (cfr) (ccli or ear99) and determined by dod to present a low risk when released out of dod control. No demil, mut, or end use certificate is required. May require an export licensefrom doc.

4. Does NSN 5999-00-413-4916 contain precious materials?

   Item contains silver.

5. Does NSN 5999-00-413-4916 contain hazardous materials?

   Indicates there is no information in the hmirs. The nsn is in a fsc in table ii of fed std 313 and a msds may be required by the user. The requirement for a msds is dependent on a hazard determination of the supplier or the intended end use of item.

6. When the NSN 5999-00-413-4916 was assigned to the Federal Catalog?

   It was assigned 56 years ago, on Fri, May 1, 1970