NSN 30B2013

A washer having a centrally located hole with a solid or laminated cross-section and two flat parallel bearing surfaces. The hole must be 75 percent or less than the largest dimension and the bearing surface finish is greater than 32 microinch (0.8 micrometer). The thickness cannot exceed 25 percent of the largest outside dimension. When the largest outside dimension is less than 1/4 inch or 6mm, the thickness must be 0.006 inches (0.15mm) or greater and for items 1/4 inch (6mm) or larger, the thickness must be 0.016 inches (0.4mm) or greater. The maximum tolerance is applied to dimensions and used as a determining factor. Items with separable lamination use shim. For items fabricated from ceramic or electrically rated materials by specification or industry standards use insulator (1), washer. Excludes:disk, valve, graphite impregnated and lubricated items.

at pole one actuator position designation, magnetic blowout arc quenching method, trip-reset actuator function, 2.480 inches minimum and 2.500 inches maximum body length, single pole type body style.

NSN 5925-01-097-1746 Datasheet

(NSN) National Stock Number

5925-01-097-1746

(FSG) Federal Supply Group

59 - Electrical and Electronic Equipment Components

(FSC) Federal Supply Classification

5925 - Circuit Breakers

(NIIN) National Item Identification Number

01-097-1746

Requires Demilitarization

Yes

(INC) Item Name Code

00136

Date

Mon, Jul 7, 1980

Schedule B Code

8536200040

Actuator Function

trip-reset

Actuator Position Designation

at pole one

Arc Quenching Method

magnetic blowout

Body Length

2.480 inches minimum and 2.500 inches maximum

Body Style

single pole type

Body Width

0.750 inches maximum

Boss Height

0.150 inches nominal

Center To Center Distance Between Terminals Parallel To Length

1.940 inches nominal

Circuit Protection Type

overcurrent single location

Distance Between Centerlines Of Mounting Facilities Parallel To Body Length

2.050 inches minimum and 2.070 inches maximum

Fragility Factor

moderately rugged

Frequency In Hertz

50.0 or 60.0 single location

Inclosure Protection Type For Which Designed

fungus resistant and moisture resistant and salt water resistant and shock resistant and vibration resistant

Internal Trip Release Configuration

series trip single location

Main Contact Tripping Mechanism Type

trip free

Manual Actuator Type And Quantity

1 toggle

Material

plastic case

Maximum Continuous Load Current Rating Per Pole

100.0 milliamperes ac single location

Maximum Interrupting Capacity Current Type And Rating Per Pole In Amps

5000.0 ac single location

Mounting Facility Type And Quantity

2 threaded hole(s)

Mounting Surface To Terminal End Distance

2.475 inches nominal

Nominal Thread Size

0.138 inches

Operating Voltage Type And Rating Per Pole In Volts

250.0 ac single location

Pole Quantity

1

Reset Method

manual

Special Handling Feature

magnetic

Storage Type

general purpose warehouse

Terminal Type And Quantity

2 threaded stud

Thread Pitch Diameters

+0.1177 to 0.1214 inches

Thread Quantity Per Inch

32

Thread Series Designator

unified national coarse (unc)

Trip Release Characteristic

time delay single location

Trip Release Method

magnetic single location

Trip Delay Time In Seconds Per Rated Continuous Current

2.000 minimum at 200 pct and 22.000 maximum at 200 pct single location

Ultimate Trip Rating Of Continuous Current Rating Per Pole In Percent

115.0 single location

Unpackaged Unit Weight

3.700 ounces nominal

Identification

Demilitarization Code

A - Items subject to the export administration regulations (ear) in parts 730-774 of title 15, code of federal regulations (cfr) (ccli or ear99) and determined by dod to present a low risk when released out of dod control. No demil, mut, or end use certificate is required. May require an export licensefrom doc.

Precious Metals Indicator

A - Item does not contain precious metal.

Hazardous Metals Indicator

P - Indicates there is no information in the hmirs. The nsn is in a fsc in table ii of fed std 313 and a msds may be required by the user. The requirement for a msds is dependent on a hazard determination of the supplier or the intended end use of item.

Pseudo Item Name Code

0000136

Cross Reference

CAGE Codes

16469

M C L, Inc.

U.s./canadian manufacturers

81541

Sensata Technologies Maryland, Inc

Non-manufacturers

Freight Information

Air Commodity

HZ -

Air Dimension

A - Shipment is not a consolidation and does not exceed 84 inches in any dimension.

National Motor Freight Class Rating

W - Rating variable

Special Handling

9 - Other or no special handling required (sh)

Type of Cargo

Z - No special type of cargo code applicable

Uniform Freight Classification Item Number

35205

Water Commodity

72D - Communications/electronics, other than sigint/ew or comsec repair parts and components

National Motor Freight Classification Item Number

063160

Schedule B & Trade

Schedule B

8536-20-0040

Description

automatic circuit breakers, for a voltage not exceeding 1,000 v, nesoi

End Use

20005 - Electric apparatus

Unit of Quantity

NO

USDA

Yes

(SITC) Standard International Trade Classification

77252

(NAICS) North American Industrial Classification System

335313

Questions & Answers

1. What is the FSCG of the NSN 5925-01-097-1746?

   The FSCG of the NSN 5925-01-097-1746 is 5925

2. Does the NSN 5925-01-097-1746 have a Schedule B code assigned?

   Yes, the Schedule B code is 8536200040

3. Does NSN 5925-01-097-1746 require demilitarization?

   Items subject to the export administration regulations (ear) in parts 730-774 of title 15, code of federal regulations (cfr) (ccli or ear99) and determined by dod to present a low risk when released out of dod control. No demil, mut, or end use certificate is required. May require an export licensefrom doc.

4. Does NSN 5925-01-097-1746 contain precious materials?

   Item does not contain precious metal.

5. Does NSN 5925-01-097-1746 contain hazardous materials?

   Indicates there is no information in the hmirs. The nsn is in a fsc in table ii of fed std 313 and a msds may be required by the user. The requirement for a msds is dependent on a hazard determination of the supplier or the intended end use of item.

6. When the NSN 5925-01-097-1746 was assigned to the Federal Catalog?

   It was assigned 46 years ago, on Mon, Jul 7, 1980