NSN C4342

A flat metal or plastic item of various peripheral shapes having a solid (not laminated) cross-section. It is designed to maintain a predetermined distance between two surfaces. For round items without a hole having a solid rectangular cross-section use disk, solid, plain. For round or hexagonal items with only one hole centrally located and with the length (thickness) exceeding 25 percent of the outside diameter or distance across peripheral flats, see spacer, sleeve. The thickness between the two parallel bearing surfaces must be 0.006 inch, (0.152 mm) or more for items less than 1/4 inch (6.35 mm) across the peripheral diameter, or smallest overall outside dimension, or must be 0.016 inch (0.406 mm) or more for items 1/4 inch (6.35 mm) or greater across the peripheral diameter or smallest overall outside dimension. For items with a thickness less than those indicated above, see shim. For items with one hole centrally located conforming to the above dimensional criteria use washer, flat or spacer, ring as applicable. When thickness and/or outsidediameter or smallest overall outside dimension is designated as a tolerance /dimension the maximum dimension will be used to determine compliance. Excludes:gasket; insulator (as modified) and mounting pad, electrical-electronic component.

0.310 inches nominal first leg distance from edge to hole center along width, one hole first leg hole arrangement style, 0.192 inches minimum and 0.198 inches maximum first leg hole diameter, 90.0 degrees nominal first leg angle, 0.380 inches nominal first leg end radius.

NSN 5340-00-527-0098 Datasheet

(NSN) National Stock Number

5340-00-527-0098

(FSG) Federal Supply Group

53 - Hardware and Abrasives

(FSC) Federal Supply Classification

5340 - Commercial Hardware

(NIIN) National Item Identification Number

00-527-0098

Requires Demilitarization

Yes

(INC) Item Name Code

16900

Date

Tue, Jan 1, 1963

Schedule B Code

8302500000

First Leg Angle

90.0 degrees nominal

First Leg Distance From Edge To Hole Center Along Width

0.310 inches nominal

First Leg End Radius

0.380 inches nominal

First Leg Hole Arrangement Style

one hole

First Leg Hole Diameter

0.192 inches minimum and 0.198 inches maximum

First Leg Distance From Edge To Hole Center Along Length

0.310 inches nominal

First Leg Style

end radius

First Leg Thickness

0.063 inches nominal

First Leg Width

0.620 inches nominal

First Leg Length

0.750 inches nominal

Material Document And Classification

mil-s-18729,cond n mil spec single material response

Material

steel comp 4130

Second Leg End Radius

0.380 inches nominal

Second Leg Hole Arrangement Style

one hole

Second Leg Hole Diameter

0.342 inches minimum and 0.349 inches maximum

Second Leg Distance From Edge To Hole Center Along Length

0.310 inches nominal

Second Leg Distance From Edge To Hole Center Along Width

0.310 inches nominal

Second Leg Thickness

0.063 inches nominal

Second Leg Width

0.620 inches nominal

Second Leg Length

1.310 inches nominal

Second Leg Relationship To First Leg

not identical

Second Leg Style

end radius

Style Designator

angle

Surface Treatment Document And Classification

qq-p-416,type 3,class 3 fed spec all treatment responses

Surface Treatment

cadmium and phosphate

Identification

Demilitarization Code

A - Items subject to the export administration regulations (ear) in parts 730-774 of title 15, code of federal regulations (cfr) (ccli or ear99) and determined by dod to present a low risk when released out of dod control. No demil, mut, or end use certificate is required. May require an export licensefrom doc.

Precious Metals Indicator

U - Precious metal content is unknown

Hazardous Metals Indicator

P - Indicates there is no information in the hmirs. The nsn is in a fsc in table ii of fed std 313 and a msds may be required by the user. The requirement for a msds is dependent on a hazard determination of the supplier or the intended end use of item.

Source of Supply Code

B17 - U.s. Army aviation & missile command (air), attn: amsmi-lc-mm-c, redstone arsenal,al 35898-5230

Pseudo Item Name Code

0016900

Cross Reference

CAGE Codes

81996

Us Army Aviation and Missile Command

Government departments or units, including military organizations

80070

Lockheed Martin Corporation Dba Lockheed Martin Rotary and Mission Systems Div Rms- C6isr

Non-manufacturers

97499

Bell Textron Inc

U.s./canadian manufacturers

16413

Cox Machine Inc

U.s./canadian manufacturers

Freight Information

Air Commodity

BZ -

Air Dimension

A - Shipment is not a consolidation and does not exceed 84 inches in any dimension.

Less than Carload Rating

Q - 70.0

National Motor Freight Class Rating

Q - 70.0

Special Handling

9 - Other or no special handling required (sh)

Type of Cargo

Z - No special type of cargo code applicable

Uniform Freight Classification Item Number

49790

Water Commodity

713 - Metal hardware

National Motor Freight Classification Item Number

095190

Schedule B & Trade

Schedule B

8302-50-0000

Description

hat-racks, hat pegs, brackets and similar fixtures, and parts thereof, of base metal

End Use

41050 - Cell phones and other household goods, n.e.c.

Unit of Quantity

KG

USDA

Yes

(SITC) Standard International Trade Classification

69919

(NAICS) North American Industrial Classification System

337215

Questions & Answers

1. What is the FSCG of the NSN 5340-00-527-0098?

   The FSCG of the NSN 5340-00-527-0098 is 5340

2. Does the NSN 5340-00-527-0098 have a Schedule B code assigned?

   Yes, the Schedule B code is 8302500000

3. Does NSN 5340-00-527-0098 require demilitarization?

   Items subject to the export administration regulations (ear) in parts 730-774 of title 15, code of federal regulations (cfr) (ccli or ear99) and determined by dod to present a low risk when released out of dod control. No demil, mut, or end use certificate is required. May require an export licensefrom doc.

4. Does NSN 5340-00-527-0098 contain precious materials?

   Precious metal content is unknown

5. Does NSN 5340-00-527-0098 contain hazardous materials?

   Indicates there is no information in the hmirs. The nsn is in a fsc in table ii of fed std 313 and a msds may be required by the user. The requirement for a msds is dependent on a hazard determination of the supplier or the intended end use of item.

6. When the NSN 5340-00-527-0098 was assigned to the Federal Catalog?

   It was assigned 63 years ago, on Tue, Jan 1, 1963