NSN HT

A flat metal or plastic item of various peripheral shapes having a solid (not laminated) cross-section. It is designed to maintain a predetermined distance between two surfaces. For round items without a hole having a solid rectangular cross-section use disk, solid, plain. For round or hexagonal items with only one hole centrally located and with the length (thickness) exceeding 25 percent of the outside diameter or distance across peripheral flats, see spacer, sleeve. The thickness between the two parallel bearing surfaces must be 0.006 inch, (0.152 mm) or more for items less than 1/4 inch (6.35 mm) across the peripheral diameter, or smallest overall outside dimension, or must be 0.016 inch (0.406 mm) or more for items 1/4 inch (6.35 mm) or greater across the peripheral diameter or smallest overall outside dimension. For items with a thickness less than those indicated above, see shim. For items with one hole centrally located conforming to the above dimensional criteria use washer, flat or spacer, ring as applicable. When thickness and/or outsidediameter or smallest overall outside dimension is designated as a tolerance /dimension the maximum dimension will be used to determine compliance. Excludes:gasket; insulator (as modified) and mounting pad, electrical-electronic component.

60.0 hertz nominal frequency rating, 400.0 milliliters bowl capacity, tachometer,autotransformer controller,automatic timer furnished controls, 8-place angle head 1,wrench 1,10 amp fuse 2,head support ring 2,rubber head seal 4,motor brush 2,3-wire cord and plug 1 accessory components and quantity, ac current type.

NSN 6640-01-033-9344 Datasheet

(NSN) National Stock Number

6640-01-033-9344

(FSG) Federal Supply Group

66 - Instruments and Laboratory Equipment

(FSC) Federal Supply Classification

6640 - Laboratory Equipment and Supplies

(NIIN) National Item Identification Number

01-033-9344

Requires Demilitarization

Yes

(INC) Item Name Code

17093

Date

Fri, Jan 14, 1977

Accessory Components And Quantity

8-place angle head 1,wrench 1,10 amp fuse 2,head support ring 2,rubber head seal 4,motor brush 2,3-wire cord and plug 1

Bowl Capacity

400.0 milliliters

Current Type

ac

Frequency Rating

60.0 hertz nominal

Furnished Controls

tachometer,autotransformer controller,automatic timer

Guard Bowl

included

Phase

single

Maximum Speed Rating In Rpm

18000.0

Operation Method

electric

Overall Depth

17.000 inches nominal

Overall Height

21.500 inches nominal

Overall Width

14.000 inches nominal

Separation Unit Type

bowl

Voltage In Volts

120.0

Identification

Demilitarization Code

A - Items subject to the export administration regulations (ear) in parts 730-774 of title 15, code of federal regulations (cfr) (ccli or ear99) and determined by dod to present a low risk when released out of dod control. No demil, mut, or end use certificate is required. May require an export licensefrom doc.

Precious Metals Indicator

U - Precious metal content is unknown

Hazardous Metals Indicator

P - Indicates there is no information in the hmirs. The nsn is in a fsc in table ii of fed std 313 and a msds may be required by the user. The requirement for a msds is dependent on a hazard determination of the supplier or the intended end use of item.

Pseudo Item Name Code

0017093

Cross Reference

CAGE Codes

16071

Iec Corporation

U.s./canadian manufacturers

Freight Information

Questions & Answers

1. What is the FSCG of the NSN 6640-01-033-9344?

   The FSCG of the NSN 6640-01-033-9344 is 6640

2. Does NSN 6640-01-033-9344 require demilitarization?

   Items subject to the export administration regulations (ear) in parts 730-774 of title 15, code of federal regulations (cfr) (ccli or ear99) and determined by dod to present a low risk when released out of dod control. No demil, mut, or end use certificate is required. May require an export licensefrom doc.

3. Does NSN 6640-01-033-9344 contain precious materials?

   Precious metal content is unknown

4. Does NSN 6640-01-033-9344 contain hazardous materials?

   Indicates there is no information in the hmirs. The nsn is in a fsc in table ii of fed std 313 and a msds may be required by the user. The requirement for a msds is dependent on a hazard determination of the supplier or the intended end use of item.

5. When the NSN 6640-01-033-9344 was assigned to the Federal Catalog?

   It was assigned 49 years ago, on Fri, Jan 14, 1977