NSN RFC-L-2200

A washer having a centrally located hole with a solid or laminated cross-section and two flat parallel bearing surfaces. The hole must be 75 percent or less than the largest dimension and the bearing surface finish is greater than 32 microinch (0.8 micrometer). The thickness cannot exceed 25 percent of the largest outside dimension. When the largest outside dimension is less than 1/4 inch or 6mm, the thickness must be 0.006 inches (0.15mm) or greater and for items 1/4 inch (6mm) or larger, the thickness must be 0.016 inches (0.4mm) or greater. The maximum tolerance is applied to dimensions and used as a determining factor. Items with separable lamination use shim. For items fabricated from ceramic or electrically rated materials by specification or industry standards use insulator (1), washer. Excludes:disk, valve, graphite impregnated and lubricated items.

unable to decode coil form type, unable to decode inductance rating, 0.880 inches minimum and 0.900 inches maximum body length, unable to decode dc resistance rating in ohms, 0.290 inches minimum and 0.310 inches maximum body outside diameter.

NSN 5950-01-080-0437 Datasheet

(NSN) National Stock Number

5950-01-080-0437

(FSG) Federal Supply Group

59 - Electrical and Electronic Equipment Components

(FSC) Federal Supply Classification

5950 - Coils and Transformers

(NIIN) National Item Identification Number

01-080-0437

Requires Demilitarization

Yes

(INC) Item Name Code

06338

Date

Thu, Jul 19, 1979

Schedule B Code

8504500000

Body Length

0.880 inches minimum and 0.900 inches maximum

Body Outside Diameter

0.290 inches minimum and 0.310 inches maximum

Coil Form Type

unable to decode

Dc Resistance Rating In Ohms

unable to decode

Inductance Rating

unable to decode

Inclosure Type

fully inclosed

Maximum Operating Temp

125.0 celsius

Mounting Method

unable to decode

Quality Factor

unable to decode

Rating Method

unable to decode

Reliability Indicator

not established

Terminal Type And Quantity

2 wire lead

Test Data Document

"81349-mil-c-15305 specification (includes engineering type bulletins, brochures,etc., that reflect specification type data in specification format; excludes commercial catalogs, industry directories, and similar trade publications, reflecting general type data on certain environmental and performance requirements and test conditions that are shown as "typical", "average", "nominal", etc.)."

Winding Operating Current

unable to decode

Identification

Demilitarization Code

A - Items subject to the export administration regulations (ear) in parts 730-774 of title 15, code of federal regulations (cfr) (ccli or ear99) and determined by dod to present a low risk when released out of dod control. No demil, mut, or end use certificate is required. May require an export licensefrom doc.

Precious Metals Indicator

U - Precious metal content is unknown

Hazardous Metals Indicator

P - Indicates there is no information in the hmirs. The nsn is in a fsc in table ii of fed std 313 and a msds may be required by the user. The requirement for a msds is dependent on a hazard determination of the supplier or the intended end use of item.

Pseudo Item Name Code

0006338

Cross Reference

CAGE Codes

49671

Lockheed Martin Corporation Dba Lockheed Martin Div Lockheed Martin

U.s./canadian manufacturers

37695

Raytheon Company

U.s./canadian manufacturers

3B150

Raytheon Company Dba Raytheon Co

U.s./canadian manufacturers

49956

Raytheon Company Div Corp

U.s./canadian manufacturers

18876

Us Army Aviation and Missile Command

Government departments or units, including military organizations

3B4M0

Lucent Technologies Inc Corporate Headquarters

Non-manufacturers

72259

Nytronics Inc

U.s./canadian manufacturers

81349

Military Specifications Promulgated by Military Departments/agencies Under Authority of Defense Standardization Manual 4120 3-M

Military standards and standards organizations (ex:stanags,milspecs,defstans)

96906

Military Standards Promulgated by Military Departments Under Authority of Defense Standardization Manual 4120 3-M

Military standards and standards organizations (ex:stanags,milspecs,defstans)

08742

Astec America Inc.

Non-manufacturers

Freight Information

Air Commodity

HZ -

Air Dimension

A - Shipment is not a consolidation and does not exceed 84 inches in any dimension.

National Motor Freight Class Rating

P - 77.5

Special Handling

9 - Other or no special handling required (sh)

Type of Cargo

Z - No special type of cargo code applicable

Uniform Freight Classification Item Number

34700

Water Commodity

595 - Transformer, (machinery and parts),(less than 35 feet)

National Motor Freight Classification Item Number

061980

Schedule B & Trade

Schedule B

8504-50-0000

Description

inductors, nesoi

End Use

20000 - Generators, accessories

Unit of Quantity

NO

USDA

Yes

(SITC) Standard International Trade Classification

77125

(NAICS) North American Industrial Classification System

334416

Questions & Answers

1. What is the FSCG of the NSN 5950-01-080-0437?

   The FSCG of the NSN 5950-01-080-0437 is 5950

2. Does the NSN 5950-01-080-0437 have a Schedule B code assigned?

   Yes, the Schedule B code is 8504500000

3. Does NSN 5950-01-080-0437 require demilitarization?

   Items subject to the export administration regulations (ear) in parts 730-774 of title 15, code of federal regulations (cfr) (ccli or ear99) and determined by dod to present a low risk when released out of dod control. No demil, mut, or end use certificate is required. May require an export licensefrom doc.

4. Does NSN 5950-01-080-0437 contain precious materials?

   Precious metal content is unknown

5. Does NSN 5950-01-080-0437 contain hazardous materials?

   Indicates there is no information in the hmirs. The nsn is in a fsc in table ii of fed std 313 and a msds may be required by the user. The requirement for a msds is dependent on a hazard determination of the supplier or the intended end use of item.

6. When the NSN 5950-01-080-0437 was assigned to the Federal Catalog?

   It was assigned 47 years ago, on Thu, Jul 19, 1979