NSN 10688470

A washer having a centrally located hole with a solid or laminated cross-section and two flat parallel bearing surfaces. The hole must be 75 percent or less than the largest dimension and the bearing surface finish is greater than 32 microinch (0.8 micrometer). The thickness cannot exceed 25 percent of the largest outside dimension. When the largest outside dimension is less than 1/4 inch or 6mm, the thickness must be 0.006 inches (0.15mm) or greater and for items 1/4 inch (6mm) or larger, the thickness must be 0.016 inches (0.4mm) or greater. The maximum tolerance is applied to dimensions and used as a determining factor. Items with separable lamination use shim. For items fabricated from ceramic or electrically rated materials by specification or industry standards use insulator (1), washer. Excludes:disk, valve, graphite impregnated and lubricated items.

compression nut connector cable strain relief method, 1000.0 single mating end single contact grouping contact maximum ac voltage rating in volts, 0.425 inches nominal cable entrance diameter, straight shape, internal coupling body style, internally threaded coupling ring connector locking method.

NSN 5935-01-070-1925 Datasheet

(NSN) National Stock Number

5935-01-070-1925

(FSG) Federal Supply Group

59 - Electrical and Electronic Equipment Components

(FSC) Federal Supply Classification

5935 - Electrical Connectors

(NIIN) National Item Identification Number

01-070-1925

Requires Demilitarization

Yes

(INC) Item Name Code

01938

Date

Sat, Jan 6, 1979

Schedule B Code

8536695050

Body Style

straight shape, internal coupling

Cable Entrance Diameter

0.425 inches nominal

Connector Cable Strain Relief Method

compression nut

Connector Locking Method

internally threaded coupling ring

Contact Maximum Ac Voltage Rating In Volts

1000.0 single mating end single contact grouping

Contact Position Arrangement Style

n single mating end

Contact Removability

removable single mating end single contact grouping

Contact Maximum Frequency Rating

11000.0 megahertz single mating end single contact grouping

Contact Surface Treatment Document And Classification

mil-g-45204,type 2,class 2 mil spec single treatment response single mating end single contact grouping

Contact Surface Treatment

gold single mating end single contact grouping

Environmental Protection

shock proof and vibration proof

Included Contact Quantity

1 single mating end single contact grouping

Included Contact Type

coaxial pin single mating end single contact grouping

Mating End Quantity

1

Nominal Thread Length

0.177 inches

Nominal Thread Size

0.625 inches

Overall Diameter

0.827 inches maximum

Overall Length

2.000 inches maximum

Precious Material And Location

contact surfaces gold

Precious Material

gold

Precious Material And Weight

0.001 gold grains, troy

Radio Frequency Type Contact Characteristic Impedance In Ohms

50.0 single mating end single contact grouping

Shell Material

copper alloy

Shell Type

solid

Specification/Standard Data

81349--39012/01 government specification

Terminal Location

back single mating end single contact grouping

Terminal Type

crimp single mating end single contact grouping

Test Data Document

"81349-mil-c-39012 specification (includes engineering type bulletins, brochures,etc., that reflect specification type data in specification format; excludes commercial catalogs, industry directories, and similar trade publications, reflecting general type data on certain environmental and performance requirements and test conditions that are shown as "typical", "average", "nominal", etc.)."

Thread Class

2b

Thread Direction

right-hand

Thread Quantity Per Inch

24

Thread Series Designator

unef

Threaded Device Type

coupling facility

Identification

Demilitarization Code

A - Items subject to the export administration regulations (ear) in parts 730-774 of title 15, code of federal regulations (cfr) (ccli or ear99) and determined by dod to present a low risk when released out of dod control. No demil, mut, or end use certificate is required. May require an export licensefrom doc.

Precious Metals Indicator

G - Item contains gold.

Hazardous Metals Indicator

P - Indicates there is no information in the hmirs. The nsn is in a fsc in table ii of fed std 313 and a msds may be required by the user. The requirement for a msds is dependent on a hazard determination of the supplier or the intended end use of item.

Pseudo Item Name Code

0001938

Cross Reference

CAGE Codes

18876

Us Army Aviation and Missile Command

Government departments or units, including military organizations

9009H

Jednolity Indeks Materialowy - Uniform Material Index

Government departments or units, including military organizations

81349

Military Specifications Promulgated by Military Departments/agencies Under Authority of Defense Standardization Manual 4120 3-M

Military standards and standards organizations (ex:stanags,milspecs,defstans)

Freight Information

Air Commodity

HZ -

Air Dimension

A - Shipment is not a consolidation and does not exceed 84 inches in any dimension.

National Motor Freight Class Rating

W - Rating variable

Special Handling

9 - Other or no special handling required (sh)

Type of Cargo

Z - No special type of cargo code applicable

Uniform Freight Classification Item Number

34570

Water Commodity

658 - Electrical appliances, small

National Motor Freight Classification Item Number

061680

Schedule B & Trade

Schedule B

8536-69-5050

Description

electrical plugs & sockets, for a voltage not exceeding 1,000 v, nesoi

End Use

20005 - Electric apparatus

Unit of Quantity

NO

USDA

Yes

(SITC) Standard International Trade Classification

77258

(NAICS) North American Industrial Classification System

335931

Questions & Answers

1. What is the FSCG of the NSN 5935-01-070-1925?

   The FSCG of the NSN 5935-01-070-1925 is 5935

2. Does the NSN 5935-01-070-1925 have a Schedule B code assigned?

   Yes, the Schedule B code is 8536695050

3. Does NSN 5935-01-070-1925 require demilitarization?

   Items subject to the export administration regulations (ear) in parts 730-774 of title 15, code of federal regulations (cfr) (ccli or ear99) and determined by dod to present a low risk when released out of dod control. No demil, mut, or end use certificate is required. May require an export licensefrom doc.

4. Does NSN 5935-01-070-1925 contain precious materials?

   Item contains gold.

5. Does NSN 5935-01-070-1925 contain hazardous materials?

   Indicates there is no information in the hmirs. The nsn is in a fsc in table ii of fed std 313 and a msds may be required by the user. The requirement for a msds is dependent on a hazard determination of the supplier or the intended end use of item.

6. When the NSN 5935-01-070-1925 was assigned to the Federal Catalog?

   It was assigned 47 years ago, on Sat, Jan 6, 1979