NSN MS24613-C212

A washer having a centrally located hole with a solid or laminated cross-section and two flat parallel bearing surfaces. The hole must be 75 percent or less than the largest dimension and the bearing surface finish is greater than 32 microinch (0.8 micrometer). The thickness cannot exceed 25 percent of the largest outside dimension. When the largest outside dimension is less than 1/4 inch or 6mm, the thickness must be 0.006 inches (0.15mm) or greater and for items 1/4 inch (6mm) or larger, the thickness must be 0.016 inches (0.4mm) or greater. The maximum tolerance is applied to dimensions and used as a determining factor. Items with separable lamination use shim. For items fabricated from ceramic or electrically rated materials by specification or industry standards use insulator (1), washer. Excludes:disk, valve, graphite impregnated and lubricated items.

up position no locking action and down position locked in and center position no locking action actuator position-locking relationship, 0.921 inches nominal actuator height, up position maintained and down position maintained and center position maintained actuator position-action relationship, natural single actuator actuator color, 0.430 inches maximum actuator diameter.

NSN 5930-00-898-0733 Datasheet

(NSN) National Stock Number

5930-00-898-0733

(FSG) Federal Supply Group

59 - Electrical and Electronic Equipment Components

(FSC) Federal Supply Classification

5930 - Switches

(NIIN) National Item Identification Number

00-898-0733

Requires Demilitarization

Yes

(INC) Item Name Code

00184

Date

Fri, Feb 10, 1967

Schedule B Code

8536509065

Actuator Height

0.921 inches nominal

Actuator Color

natural single actuator

Actuator Diameter

0.430 inches maximum

Actuator Position-Action Relationship

up position maintained and down position maintained and center position maintained

Actuator Position-Locking Relationship

up position no locking action and down position locked in and center position no locking action

Actuator Style

round

Body Length

1.336 inches maximum

Body Style

bushing mount

Body Width

1.015 inches maximum

Bushing Length

0.469 inches nominal

Contact Load Current Rating At Maximum Rated Voltage

25.000 amperes resistive dc and 15.000 amperes inductive dc and 7.000 amperes lamp dc and 25.000 amperes resistive ac and 15.000 amperes inductive ac and 7.000 amperes lamp ac

Features Provided

actuator seal

Hazardous Locations/Environmental Protection

weatherproof

Inclosure Type

fully inclosed

Material

plastic case

Maximum Voltage Rating In Volts

115.0 ac and 28.0 dc

Mounting Method

threaded bushing

Mounting Surface To Terminal End Distance

1.203 inches maximum

Nominal Thread Size

0.469 inches

Nonpile-Up Contact Arrangement

2 pole, double throw, three positions maintained single switch unit

Overall Height

2.593 inches nominal

Overall Length

1.336 inches maximum

Overall Width

1.015 inches maximum

Precious Material And Location

terminals silver

Specification/Standard Data

96906-ms24613 government standard

Terminal Type And Quantity

6 tab w/screw

Test Data Document

"81349-mil-s-8834 specification (includes engineering type bulletins, brochures,etc., that reflect specification type data in specification format; excludes commercial catalogs, industry directories, and similar trade publications, reflecting general type data on certain environmental and performance requirements and test conditions that are shown as "typical", "average", "nominal", etc.)."

Thread Quantity Per Inch

32

Thread Series Designator

uns

Identification

Demilitarization Code

A - Items subject to the export administration regulations (ear) in parts 730-774 of title 15, code of federal regulations (cfr) (ccli or ear99) and determined by dod to present a low risk when released out of dod control. No demil, mut, or end use certificate is required. May require an export licensefrom doc.

Precious Metals Indicator

S - Item contains silver.

Hazardous Metals Indicator

P - Indicates there is no information in the hmirs. The nsn is in a fsc in table ii of fed std 313 and a msds may be required by the user. The requirement for a msds is dependent on a hazard determination of the supplier or the intended end use of item.

Pseudo Item Name Code

0000184

Cross Reference

CAGE Codes

81640

Safran Power Usa, Llc

U.s./canadian manufacturers

96906

Military Standards Promulgated by Military Departments Under Authority of Defense Standardization Manual 4120 3-M

Military standards and standards organizations (ex:stanags,milspecs,defstans)

Freight Information

Air Commodity

HZ -

Air Dimension

A - Shipment is not a consolidation and does not exceed 84 inches in any dimension.

National Motor Freight Class Rating

M - 85.0

Special Handling

9 - Other or no special handling required (sh)

Type of Cargo

Z - No special type of cargo code applicable

Uniform Freight Classification Item Number

34430

Water Commodity

72D - Communications/electronics, other than sigint/ew or comsec repair parts and components

National Motor Freight Classification Item Number

061360

Schedule B & Trade

Schedule B

8536-50-9065

Description

switches, for a voltage not exceeding 1000 volts, nesoi

End Use

20005 - Electric apparatus

Unit of Quantity

NO

USDA

Yes

(SITC) Standard International Trade Classification

77255

(NAICS) North American Industrial Classification System

335931

Questions & Answers

1. What is the FSCG of the NSN 5930-00-898-0733?

   The FSCG of the NSN 5930-00-898-0733 is 5930

2. Does the NSN 5930-00-898-0733 have a Schedule B code assigned?

   Yes, the Schedule B code is 8536509065

3. Does NSN 5930-00-898-0733 require demilitarization?

   Items subject to the export administration regulations (ear) in parts 730-774 of title 15, code of federal regulations (cfr) (ccli or ear99) and determined by dod to present a low risk when released out of dod control. No demil, mut, or end use certificate is required. May require an export licensefrom doc.

4. Does NSN 5930-00-898-0733 contain precious materials?

   Item contains silver.

5. Does NSN 5930-00-898-0733 contain hazardous materials?

   Indicates there is no information in the hmirs. The nsn is in a fsc in table ii of fed std 313 and a msds may be required by the user. The requirement for a msds is dependent on a hazard determination of the supplier or the intended end use of item.

6. When the NSN 5930-00-898-0733 was assigned to the Federal Catalog?

   It was assigned 59 years ago, on Fri, Feb 10, 1967