NSN MS3113H14C19PW

A washer having a centrally located hole with a solid or laminated cross-section and two flat parallel bearing surfaces. The hole must be 75 percent or less than the largest dimension and the bearing surface finish is greater than 32 microinch (0.8 micrometer). The thickness cannot exceed 25 percent of the largest outside dimension. When the largest outside dimension is less than 1/4 inch or 6mm, the thickness must be 0.006 inches (0.15mm) or greater and for items 1/4 inch (6mm) or larger, the thickness must be 0.016 inches (0.4mm) or greater. The maximum tolerance is applied to dimensions and used as a determining factor. Items with separable lamination use shim. For items fabricated from ceramic or electrically rated materials by specification or industry standards use insulator (1), washer. Excludes:disk, valve, graphite impregnated and lubricated items.

unable to decode contact position arrangement style, bayonet pin connector locking method, unable to decode contact material, straight shape w/solder mount body style, round bushing accommodation hole shape.

NSN 5935-00-901-7029 Datasheet

(NSN) National Stock Number

5935-00-901-7029

(FSG) Federal Supply Group

59 - Electrical and Electronic Equipment Components

(FSC) Federal Supply Classification

5935 - Electrical Connectors

(NIIN) National Item Identification Number

00-901-7029

Requires Demilitarization

Yes

(INC) Item Name Code

15093

Date

Fri, Jan 1, 1960

Schedule B Code

8538907080

Body Style

straight shape w/solder mount

Bushing Accommodation Hole Shape

round

Connector Locking Method

bayonet pin

Contact Material

unable to decode

Contact Position Arrangement Style

unable to decode

Contact Removability

unable to decode

Contact Maximum Ac Voltage Rating In Volts

unable to decode

Contact Surface Treatment Document And Classification

unable to decode

Contact Surface Treatment

unable to decode

Environmental Protection

moisture proof and salt water resistant and vibration proof and thermal shock resistant and corrosion resistant

Included Contact Quantity

unable to decode

Included Contact Type

unable to decode

Insert Material

unable to decode

Insert Position In Deg

30.0

Mating End Quantity

1

Operating Temp Rating

-55.0 celsius minimum and 125.0 celsius maximum

Overall Diameter

0.953 inches minimum and 0.985 inches maximum

Overall Length

0.828 inches maximum

Polarization Method

keyway or multiple keyway

Precious Material And Location

contact surfaces gold

Precious Material

gold

Precious Material And Weight

0.019 gold grains, troy

Shell Surface Treatment Document And Classification

mil-t-10727,ty 1 mil spec single treatment response

Shell Material

steel

Shell Surface Treatment

tin

Shell Type

solid

Specification/Standard Data

96906-ms3113 government standard

Terminal Location

unable to decode

Terminal Type

unable to decode

Test Data Document

"81349-mil-c-26482 specification (includes engineering type bulletins, brochures,etc., that reflect specification type data in specification format; excludes commercial catalogs, industry directories, and similar trade publications, reflecting general type data on certain environmental and performance requirements and test conditions that are shown as "typical", "average", "nominal", etc.)."

Identification

Demilitarization Code

A - Items subject to the export administration regulations (ear) in parts 730-774 of title 15, code of federal regulations (cfr) (ccli or ear99) and determined by dod to present a low risk when released out of dod control. No demil, mut, or end use certificate is required. May require an export licensefrom doc.

Precious Metals Indicator

G - Item contains gold.

Hazardous Metals Indicator

P - Indicates there is no information in the hmirs. The nsn is in a fsc in table ii of fed std 313 and a msds may be required by the user. The requirement for a msds is dependent on a hazard determination of the supplier or the intended end use of item.

Pseudo Item Name Code

0015093

Cross Reference

CAGE Codes

94580

Honeywell International Inc. Dba Honeywell International Div Aerospace-Minneapolis

U.s./canadian manufacturers

96906

Military Standards Promulgated by Military Departments Under Authority of Defense Standardization Manual 4120 3-M

Military standards and standards organizations (ex:stanags,milspecs,defstans)

77820

Amphenol Corp Div Amphenol Aerospace Operations

U.s./canadian manufacturers

Freight Information

Air Commodity

HZ -

Air Dimension

A - Shipment is not a consolidation and does not exceed 84 inches in any dimension.

National Motor Freight Class Rating

W - Rating variable

Special Handling

9 - Other or no special handling required (sh)

Type of Cargo

Z - No special type of cargo code applicable

Uniform Freight Classification Item Number

34570

Water Commodity

72D - Communications/electronics, other than sigint/ew or comsec repair parts and components

National Motor Freight Classification Item Number

061680

Schedule B & Trade

Schedule B

8538-90-7080

Description

parts suitable for use solely or principally with the apparatus for heading 8535, 8536,8537, nesoi

End Use

20005 - Electric apparatus

Unit of Quantity

NO

USDA

Yes

(SITC) Standard International Trade Classification

77282

(NAICS) North American Industrial Classification System

335314

Questions & Answers

1. What is the FSCG of the NSN 5935-00-901-7029?

   The FSCG of the NSN 5935-00-901-7029 is 5935

2. Does the NSN 5935-00-901-7029 have a Schedule B code assigned?

   Yes, the Schedule B code is 8538907080

3. Does NSN 5935-00-901-7029 require demilitarization?

   Items subject to the export administration regulations (ear) in parts 730-774 of title 15, code of federal regulations (cfr) (ccli or ear99) and determined by dod to present a low risk when released out of dod control. No demil, mut, or end use certificate is required. May require an export licensefrom doc.

4. Does NSN 5935-00-901-7029 contain precious materials?

   Item contains gold.

5. Does NSN 5935-00-901-7029 contain hazardous materials?

   Indicates there is no information in the hmirs. The nsn is in a fsc in table ii of fed std 313 and a msds may be required by the user. The requirement for a msds is dependent on a hazard determination of the supplier or the intended end use of item.

6. When the NSN 5935-00-901-7029 was assigned to the Federal Catalog?

   It was assigned 66 years ago, on Fri, Jan 1, 1960