NSN SCDL26752

A washer having a centrally located hole with a solid or laminated cross-section and two flat parallel bearing surfaces. The hole must be 75 percent or less than the largest dimension and the bearing surface finish is greater than 32 microinch (0.8 micrometer). The thickness cannot exceed 25 percent of the largest outside dimension. When the largest outside dimension is less than 1/4 inch or 6mm, the thickness must be 0.006 inches (0.15mm) or greater and for items 1/4 inch (6mm) or larger, the thickness must be 0.016 inches (0.4mm) or greater. The maximum tolerance is applied to dimensions and used as a determining factor. Items with separable lamination use shim. For items fabricated from ceramic or electrically rated materials by specification or industry standards use insulator (1), washer. Excludes:disk, valve, graphite impregnated and lubricated items.

qq-c-530 fed spec single material response single mating end single contact grouping contact material document and classification, compression nut connector cable strain relief method, 0.900 inches nominal cable entrance diameter, internally threaded coupling ring connector locking method, straight shape, internal coupling body style.

NSN 5935-00-944-4453 Datasheet

(NSN) National Stock Number

5935-00-944-4453

(FSG) Federal Supply Group

59 - Electrical and Electronic Equipment Components

(FSC) Federal Supply Classification

5935 - Electrical Connectors

(NIIN) National Item Identification Number

00-944-4453

Requires Demilitarization

Yes

(INC) Item Name Code

01938

Date

Fri, Feb 11, 1966

Schedule B Code

8536695050

Body Style

straight shape, internal coupling

Cable Entrance Diameter

0.900 inches nominal

Connector Cable Strain Relief Method

compression nut

Connector Locking Method

internally threaded coupling ring

Contact Material Document And Classification

qq-c-530 fed spec single material response single mating end single contact grouping

Contact Material

copper alloy single mating end single contact grouping

Contact Position Arrangement Style

lc single mating end

Contact Removability

removable single mating end single contact grouping

Contact Maximum Ac Voltage Rating In Volts

5000.0 single mating end single contact grouping

Contact Surface Treatment Document And Classification

qq-s-365 fed spec single treatment response single mating end single contact grouping

Contact Surface Treatment

silver single mating end single contact grouping

Environmental Protection

corrosion resistant

Included Contact Quantity

1 single mating end single contact grouping

Included Contact Type

coaxial pin single mating end single contact grouping

Insert Material

plastic tetrafluoroethylene single mating end

Mating End Quantity

1

Nominal Thread Size

1.250 inches

Overall Diameter

1.625 inches nominal

Overall Length

2.625 inches nominal

Precious Material And Location

contact and shell surfaces silver

Precious Material And Weight

0.105 silver grains, troy

Precious Material

silver

Radio Frequency Type Contact Characteristic Impedance In Ohms

50.0 single mating end single contact grouping

Shell Material

copper alloy

Shell Surface Treatment Document And Classification

qq-s-365 fed spec single treatment response

Shell Surface Treatment

silver

Shell Type

solid

Specification/Standard Data

96906-ms27140 government standard

Terminal Location

back single mating end single contact grouping

Terminal Type

crimp single mating end single contact grouping

Test Data Document

"81349-mil-c-3650 specification (includes engineering type bulletins, brochures,etc., that reflect specification type data in specification format; excludes commercial catalogs, industry directories, and similar trade publications, reflecting general type data on certain environmental and performance requirements and test conditions that are shown as "typical", "average", "nominal", etc.)."

Thread Class

2b

Thread Direction

right-hand

Thread Quantity Per Inch

18

Thread Series Designator

unef

Threaded Device Type

coupling facility

Identification

Demilitarization Code

A - Items subject to the export administration regulations (ear) in parts 730-774 of title 15, code of federal regulations (cfr) (ccli or ear99) and determined by dod to present a low risk when released out of dod control. No demil, mut, or end use certificate is required. May require an export licensefrom doc.

Precious Metals Indicator

S - Item contains silver.

Hazardous Metals Indicator

P - Indicates there is no information in the hmirs. The nsn is in a fsc in table ii of fed std 313 and a msds may be required by the user. The requirement for a msds is dependent on a hazard determination of the supplier or the intended end use of item.

Pseudo Item Name Code

0001938

Cross Reference

CAGE Codes

96906

Military Standards Promulgated by Military Departments Under Authority of Defense Standardization Manual 4120 3-M

Military standards and standards organizations (ex:stanags,milspecs,defstans)

80063

Us Army Communications & Electronics Materiel Readiness Command Logistics Engineering Dir

U.s./canadian manufacturers

80058

Joint Electronics Type Designation System

Military standards and standards organizations (ex:stanags,milspecs,defstans)

94375

Lax Electronics, Inc. Dba Automatic Connector Div Automatic Connector

U.s./canadian manufacturers

91836

Winchester Interconnect Corporation

U.s./canadian manufacturers

92180

Winchester Interconnect Rf Corporation

U.s./canadian manufacturers

Freight Information

Air Commodity

HZ -

Air Dimension

A - Shipment is not a consolidation and does not exceed 84 inches in any dimension.

National Motor Freight Class Rating

W - Rating variable

Special Handling

9 - Other or no special handling required (sh)

Type of Cargo

Z - No special type of cargo code applicable

Uniform Freight Classification Item Number

34570

Water Commodity

658 - Electrical appliances, small

National Motor Freight Classification Item Number

061680

Schedule B & Trade

Schedule B

8536-69-5050

Description

electrical plugs & sockets, for a voltage not exceeding 1,000 v, nesoi

End Use

20005 - Electric apparatus

Unit of Quantity

NO

USDA

Yes

(SITC) Standard International Trade Classification

77258

(NAICS) North American Industrial Classification System

335931

Questions & Answers

1. What is the FSCG of the NSN 5935-00-944-4453?

   The FSCG of the NSN 5935-00-944-4453 is 5935

2. Does the NSN 5935-00-944-4453 have a Schedule B code assigned?

   Yes, the Schedule B code is 8536695050

3. Does NSN 5935-00-944-4453 require demilitarization?

   Items subject to the export administration regulations (ear) in parts 730-774 of title 15, code of federal regulations (cfr) (ccli or ear99) and determined by dod to present a low risk when released out of dod control. No demil, mut, or end use certificate is required. May require an export licensefrom doc.

4. Does NSN 5935-00-944-4453 contain precious materials?

   Item contains silver.

5. Does NSN 5935-00-944-4453 contain hazardous materials?

   Indicates there is no information in the hmirs. The nsn is in a fsc in table ii of fed std 313 and a msds may be required by the user. The requirement for a msds is dependent on a hazard determination of the supplier or the intended end use of item.

6. When the NSN 5935-00-944-4453 was assigned to the Federal Catalog?

   It was assigned 60 years ago, on Fri, Feb 11, 1966